skip to Main Content
Select Currency:
Currency:

Throttle linkage kits to suit 4age 20V throttles

Rated 0 out of 5
(be the first to review)

$150.00

Description

Throttle linkage kits to suit 4age 20V throttles

These kits replace the original 4age 20V top linkage system and in it’s place has the throttle cable directly actuate the opening of the throttle bodies from the underside. For those that use 4age 16V engines converted to quad throttles this gives a significant improvement in the throttle feel due to the throttle cable path.

Two different kits are available, please read below on which type is suitable and select from the drop-down box to purchase.

 

Features and advantages

– Throttle cable routing: These kits on offer relocate the throttle cable to the middle of the 2nd and 3rd throttles from the bottom up. This helps to hide and remove any harsh bends in the throttle cable.

– Throttle cable angle: Both of the throttle cable brackets hold the cable on an angle away from the throttle bodys faces, this gives enough clearance to run a large airbox if required.

– Actuation: With the removal of the joints between the cable and throttle bodies the cable is able to directly control the opening of the throttles. This results in an improvement in the throttle feel and allow for the most precise control possible – better than when these where released from new!

– Appearance: When one of these kits are fitted the original brackets and links are removed from the top of the throttles and the throttle cable is ran under and out of sight. With these changes the engine and the engine bay will look simpler and neater.

– Construction: The throttle cable retainer brackets are made from 2.5mm thick stainless plate. The throttle end links are plated steel. These materials where chosen to be completely rigid and have a near indefinite working life.

 

Product option 1: Standard Down-pull kit

Suits throttles that are mounted upright as per OEM fitment on a 20V engine – this is where the Throttle position sensor (TPS) is held at the front of the engine.

– Compatible with the block to throttle body support straps as fitted to 4age 20V engines.

– No modifications required to the throttle bodies.

 

Product option 2: Reverse Down-pull kit – for inverted throttles

Suits throttles that have been mounted upside down – this is where the Throttle position sensor (TPS) is held at the rear of the engine.

On engines such as the 4age 16V that have been converted to quad throttles the throttles are held in place upside down. This when fitted to a right hand drive car with a rear wheel drive engine forces the throttle cable into a torturous path with two very harsh bends. The end is a stiff throttle pedal with poor feedback. This kit complete fixes this issue but running the cable in a gentle loop around the bottom and up.

– Note: to fit this version a small part of the OEM throttle end link needs to be removed, this is easily cut off with a hand grinder or a hand saw.

 

Throttle body and intake manifold compatibility

– Throttle spacing: The supplied brackets with the kits suit different ranges of spacing from the centre to centre between throttles from the original 20V (87.5mm) right up to 93mm.

– 3sge Beams: Compatible with our 3sge Beams adapter (pictured).

– Throttles: Suit all three of the 20V 4age throttle types.

– Throttle cable type: Due to being able to be routed around or under the brake master cylinder the throttle cable used can vary a great deal in it’s length. When fitted to an AE71 or AE86 model Corolla / Sprinter even the very long KE70 cable can be used, the original type as used with a 4age 16V engine in a RHD AE86 is not likely to fit.

– Throttle lift-off valve / actuator: From standard there is a small pneumatic actuator bolted between the 2nd and 3rd throttles on the underside. This can not be retained after the installation of either linkage kit. There is little to no downside in removing this OEM part and plugging the left over rubber vacuum hose.

 

Airbox and intake plate compatibility

These linkage kits are compatible with a wide range of intake plates / airbox options. They may however not clear an airbox that curves inwards. For example these are incompatible with either of the factory fitted 20V airboxes and the aftermarket option from Mekaru.

 

Additional information

Weight 0.25 kg
Dimensions 5 × 5 × 2 cm
Type of kit

,

1 review for Throttle linkage kits to suit 4age 20V throttles

  1. Snot Rocket.

    Brilliant as always

    Just a heads up on how well the throttle kit fits the Westfield Clubman. The bracket bolted on with good clearance, and my cable goes from 1200mm long with 180 degree bend to 500mm long with 90 degree bend and 100 mm radius. Took about 30 minutes to fit up, and the exact same cable throw resulted, so the throttel stops on my pedal box didnt even need adjustimng. Keep up the good work..

Leave a customer review

Your email address will not be published. Required fields are marked *

Back To Top